Rootserver RAID- / Bootproblem, 1&1 *Update*

Alles was in keine andere Systemkategorie passt
shapeshift
Posts: 18
Joined: 2003-02-16 00:05
 

Rootserver RAID- / Bootproblem, 1&1 *Update*

Post by shapeshift »

Hallo zusammen,

habe ein grösseres Problem mit meinem Rootie - er ist momentan nicht erreichbar aufgrund eines RAID/Boot-Problems,
nach diversen Tests komme ich gerade einfach nicht weiter :-(

*** In den nächsten Beiträgen sind noch weitere Details enthalten ***

Daten:
1&1 RootServer L64, Suse10.3, Plesk 8.6.0

Problem:
Gestern nachmittag ab ca. 15:15 war der Server nicht mehr via www,pop/imap, ping erreichbar, ich habe die üblichen Verdächtigen in den Logfiles angeschaut, aber keinen entscheidenden Hinweis erhalten (Zugriff per Sercon-Konsole war möglich).

Ich habe kontrolliert dass alle Nutzer-Daten OK sind, dann mit shutdown -rn now einen Neustart versucht.

Beim Neustart wird nicht richtig gemountet, musste dann ins Rescue.

Im Rescue dann

Code: Select all

mount /dev/md1 /mnt
mount /dev/md6 /mnt/var
mount /dev/md5 /mnt/usr
mount /dev/md7 /mnt/home
mount /dev/md8 /mnt/srv
chroot /mnt
/etc/init.d/psa start
>>> System funktioniert, Server im Internet erreichbar, Plesk funktioniert

Code: Select all

lilo
>>> Bootloader neu (später nochmals auch mit -v -t gestartet)

Code: Select all

/etc/init.d/psa stopall
exit
umount /mnt
>>> Einstellung 1&1 Normal Booten (ohne Checkbox "Sofort")

Code: Select all

shutdown -rn now
>>> System startet fehlerhaft neu (es wird nichts gemountet)
>>> ich muss dann immer wieder ins Rescue-System

Bootvorgang dann protokolliert und folgendes bemerkt:

Code: Select all

...
md: md1 stopped.
Loading ext3
mdadm: no devices found for /dev/md1
Waiting for device /dev/root to appear:  ok
/dev/root: unknown volume type
invalid root filesystem -- exiting to /bin/sh
Woran genau liegt das? Ideen? Tipps?
Liegt ein HW-Defekt vor?
Das Raid scheint ja nicht zu funktionieren bzw. beim Booten kann es nicht
verwendet werden und deshalb bricht das System dann ab, oder?
Ich sehe auch dass die beiden Inhalte von sda1 und sda2 unterschiedlich sind.
Ich habe die Threads bezüglich "lilo" gelesen, hatte aber damit leider keinen Erfolg.
Auch bereits fsck bzw. fsck.ext3 durchgeführt und xfs_repair.
Dann noch das Problem mit dem Kernel-Update bei 1&1 gesehen, sieht hier aber wohl nicht so aus, dass das zutreffen würde.

Nachfolgend einige Logfiles und weitere Informationen,
falls noch mehr Daten benötigt werden bitte kurze Info.

Vielen Dank im voraus für Eure Unterstützung!

----------------------------------------------
NACHFOLGENDE DATEN ALLE IM RESCUE MODUS ERSTELLT:

Code: Select all

fdisk -l

Code: Select all

Disk /dev/sda: 160.0 GB, 160041885696 bytes
255 heads, 63 sectors/track, 19457 cylinders
Units = cylinders of 16065 * 512 = 8225280 bytes

   Device Boot      Start         End      Blocks   Id  System
/dev/sda1               1         123      987966   fd  Linux raid autodetect
/dev/sda2             124         367     1959930   82  Linux swap / Solaris
/dev/sda4             368       19457   153340425    5  Extended
/dev/sda5             368         976     4891761   fd  Linux raid autodetect
/dev/sda6             977        1585     4891761   fd  Linux raid autodetect
/dev/sda7            1586        4018    19543041   fd  Linux raid autodetect
/dev/sda8            4019       19457   124013736   fd  Linux raid autodetect

Disk /dev/sdb: 160.0 GB, 160041885696 bytes
255 heads, 63 sectors/track, 19457 cylinders
Units = cylinders of 16065 * 512 = 8225280 bytes

   Device Boot      Start         End      Blocks   Id  System
/dev/sdb1               1         123      987966   fd  Linux raid autodetect
/dev/sdb2             124         367     1959930   82  Linux swap / Solaris
/dev/sdb4             368       19457   153340425    5  Extended
/dev/sdb5             368         976     4891761   fd  Linux raid autodetect
/dev/sdb6             977        1585     4891761   fd  Linux raid autodetect
/dev/sdb7            1586        4018    19543041   fd  Linux raid autodetect
/dev/sdb8            4019       19457   124013736   fd  Linux raid autodetect

Disk /dev/md8: 126.9 GB, 126989959168 bytes
2 heads, 4 sectors/track, 31003408 cylinders
Units = cylinders of 8 * 512 = 4096 bytes

Disk /dev/md8 doesn't contain a valid partition table

Disk /dev/md7: 20.0 GB, 20012007424 bytes
2 heads, 4 sectors/track, 4885744 cylinders
Units = cylinders of 8 * 512 = 4096 bytes

Disk /dev/md7 doesn't contain a valid partition table

Disk /dev/md6: 5009 MB, 5009047552 bytes
2 heads, 4 sectors/track, 1222912 cylinders
Units = cylinders of 8 * 512 = 4096 bytes

Disk /dev/md6 doesn't contain a valid partition table

Disk /dev/md5: 5009 MB, 5009047552 bytes
2 heads, 4 sectors/track, 1222912 cylinders
Units = cylinders of 8 * 512 = 4096 bytes

Disk /dev/md5 doesn't contain a valid partition table

Disk /dev/md1: 1011 MB, 1011548160 bytes
2 heads, 4 sectors/track, 246960 cylinders
Units = cylinders of 8 * 512 = 4096 bytes

Disk /dev/md1 doesn't contain a valid partition table
----------------------------------------------

Code: Select all

mdadm -D /dev/md1

Code: Select all

/dev/md1:
        Version : 00.90.03
  Creation Time : Mon Feb  6 06:28:25 2006
     Raid Level : raid1
     Array Size : 987840 (964.69 MiB 1011.55 MB)
    Device Size : 987840 (964.69 MiB 1011.55 MB)
   Raid Devices : 2
  Total Devices : 1
Preferred Minor : 1
    Persistence : Superblock is persistent

    Update Time : Sat Jan 17 10:01:17 2009
          State : clean, degraded
 Active Devices : 1
Working Devices : 1
 Failed Devices : 0
  Spare Devices : 0

           UUID : e78c4df1:f49e231b:93396609:43713abc
         Events : 0.2941094

    Number   Major   Minor   RaidDevice State
       0       8        1        0      active sync   /dev/sda1
       1       0        0        -      removed

----------------------------------------------

Code: Select all

var/log/messages

Code: Select all

Jan 16 15:15:01 s1XXXXXXX /usr/sbin/cron[26847]: (mailman) CMD (/usr/bin/python
-S /usr/lib/mailman/cron/gate_news)
Jan 16 15:17:21 s1XXXXXXX pop3d: 1232115441.302431 TIMEOUT, user=info@domain.de, ip=[80.187.102.228], top=0, retr=0, time=301, rcvd=12, sent=44, mail
dir=/var/qmail/mailnames/domain.de/info/Maildir
Jan 16 15:17:23 s1XXXXXXX pop3d: 1232115443.302499 TIMEOUT, user=reservierung@domain.de, ip=[80.187.102.228], top=0, retr=0, time=301, rcvd=12, sent=3
8, maildir=/var/qmail/mailnames/domain.de/reservierung/Maildir
Jan 16 15:17:23 s1XXXXXXX pop3d: 1232115443.490494 TIMEOUT, user=info@domain.de, ip=[80.187.102.228], top=0, retr=0, time=301, rcvd=12, sent=41, maild
ir=/var/qmail/mailnames/domain.de/info/Maildir
Jan 16 15:17:23 s1XXXXXXX pop3d: 1232115443.542491 TIMEOUT, user=info@domain.de, ip=[80.187.102.228], top=0, retr=0, time=301, rcvd=12, sent=45, mail
dir=/var/qmail/mailnames/domain.de/info/Maildir
Jan 16 15:20:01 s1XXXXXXX /usr/sbin/cron[26870]: (mailman) CMD (/usr/bin/python-S /usr/lib/mailman/cron/gate_news)
Jan 16 15:22:01 s1XXXXXXX /usr/sbin/cron[26872]: (root) CMD (/usr/local/psa/admin/sbin/backupmng >/dev/null 2>&1)
Jan 16 15:25:01 s1XXXXXXX /usr/sbin/cron[26876]: (mailman) CMD (/usr/bin/python-S /usr/lib/mailman/cron/gate_news)
Jan 16 15:30:01 s1XXXXXXX /usr/sbin/cron[26881]: (mailman) CMD (/usr/bin/python-S /usr/lib/mailman/cron/gate_news)
Jan 16 15:35:01 s1XXXXXXX /usr/sbin/cron[26904]: (mailman) CMD (/usr/bin/python-S /usr/lib/mailman/cron/gate_news)
Jan 16 15:37:01 s1XXXXXXX /usr/sbin/cron[26906]: (root) CMD (/usr/local/psa/admin/sbin/backupmng >/dev/null 2>&1)
Jan 16 15:40:01 s1XXXXXXX /usr/sbin/cron[26910]: (mailman) CMD (/usr/bin/python-S /usr/lib/mailman/cron/gate_news)
Jan 16 15:45:01 s1XXXXXXX /usr/sbin/cron[26913]: (mailman) CMD (/usr/bin/python-S /usr/lib/mailman/cron/gate_news)
Jan 16 15:45:06 s1XXXXXXX syslog-ng[4389]: STATS: dropped 180
Jan 16 15:50:01 s1XXXXXXX /usr/sbin/cron[26938]: (mailman) CMD (/usr/bin/python-S /usr/lib/mailman/cron/gate_news)
Jan 16 15:52:01 s1XXXXXXX /usr/sbin/cron[26940]: (root) CMD (/usr/local/psa/admin/sbin/backupmng >/dev/null 2>&1)
Jan 16 15:55:01 s1XXXXXXX /usr/sbin/cron[26944]: (mailman) CMD (/usr/bin/python-S /usr/lib/mailman/cron/gate_news)
Jan 16 16:00:01 s1XXXXXXX /usr/sbin/cron[26949]: (mailman) CMD (/usr/bin/python-S /usr/lib/mailman/cron/gate_news)
Jan 16 16:05:01 s1XXXXXXX /usr/sbin/cron[26983]: (mailman) CMD (/usr/bin/python-S /usr/lib/mailman/cron/gate_news)
Jan 16 16:07:01 s1XXXXXXX /usr/sbin/cron[26985]: (root) CMD (/usr/local/psa/admin/sbin/backupmng >/dev/null 2>&1)
Jan 16 16:10:01 s1XXXXXXX /usr/sbin/cron[26989]: (mailman) CMD (/usr/bin/python-S /usr/lib/mailman/cron/gate_news)
Jan 16 16:15:01 s1XXXXXXX /usr/sbin/cron[26994]: (mailman) CMD (/usr/bin/python-S /usr/lib/mailman/cron/gate_news)
Jan 16 16:20:01 s1XXXXXXX /usr/sbin/cron[27017]: (mailman) CMD (/usr/bin/python-S /usr/lib/mailman/cron/gate_news)
Jan 16 16:22:01 s1XXXXXXX /usr/sbin/cron[27019]: (root) CMD (/usr/local/psa/admin/sbin/backupmng >/dev/null 2>&1)
Jan 16 16:25:01 s1XXXXXXX /usr/sbin/cron[27023]: (mailman) CMD (/usr/bin/python-S /usr/lib/mailman/cron/gate_news)
Jan 16 16:30:01 s1XXXXXXX /usr/sbin/cron[27028]: (mailman) CMD (/usr/bin/python-S /usr/lib/mailman/cron/gate_news)
Jan 16 16:35:01 s1XXXXXXX /usr/sbin/cron[27051]: (mailman) CMD (/usr/bin/python-S /usr/lib/mailman/cron/gate_news)
Jan 16 16:37:01 s1XXXXXXX /usr/sbin/cron[27053]: (root) CMD (/usr/local/psa/admin...
.
.
.
Jan 16 19:01:07 s1XXXXXXX kernel: sd 1:0:0:0: SCSI error: return code = 0x00040000
Jan 16 19:01:07 s1XXXXXXX kernel: end_request: I/O error, dev sdb, sector 0
Jan 16 19:01:07 s1XXXXXXX kernel: Buffer I/O error on device sdb, logical block0
Jan 16 19:01:07 s1XXXXXXX kernel: Buffer I/O error on device sdb, logical block1
Jan 16 19:01:07 s1XXXXXXX kernel: Buffer I/O error on device sdb, logical block2
Jan 16 19:01:07 s1XXXXXXX kernel: Buffer I/O error on device sdb, logical block3
Jan 16 19:01:07 s1XXXXXXX kernel: klogd 1.4.1, ---------- state change ---------
-
Jan 16 19:01:07 s1XXXXXXX kernel: sd 1:0:0:0: SCSI error: return code = 0x00040000
Jan 16 19:01:07 s1XXXXXXX kernel: end_request: I/O error, dev sdb, sector 0
Jan 16 19:01:07 s1XXXXXXX kernel: Buffer I/O error on device sdb, logical block0
Jan 16 19:01:08 s1XXXXXXX kernel: sd 1:0:0:0: SCSI error: return code = 0x00040000
Jan 16 19:01:08 s1XXXXXXX kernel: end_request: I/O error, dev sdb, sector 312581800
Jan 16 19:01:08 s1XXXXXXX kernel: Buffer I/O error on device sdb, logical block 39072725
Jan 16 19:01:08 s1XXXXXXX kernel: sd 1:0:0:0: SCSI error: return code = 0x00040000
Jan 16 19:01:08 s1XXXXXXX kernel: end_request: I/O error, dev sdb, sector 312581800
Jan 16 19:01:08 s1XXXXXXX kernel: Buffer I/O error on device sdb, logical block 39072725
Jan 16 19:01:08 s1XXXXXXX kernel: sd 1:0:0:0: SCSI error: return code = 0x00040000
Jan 16 19:01:08 s1XXXXXXX kernel: end_request: I/O error, dev sdb, sector 312581800
Jan 16 19:01:08 s1XXXXXXX kernel: Buffer I/O error on device sdb, logical block 39072725
Jan 16 19:01:08 s1XXXXXXX kernel: sd 1:0:0:0: SCSI error: return code = 0x00040000
Jan 16 19:01:08 s1XXXXXXX kernel: end_request: I/O error, dev sdb, sector 312581544
Jan 16 19:01:08 s1XXXXXXX kernel: Buffer I/O error on device sdb, logical block 39072693
Jan 16 19:01:08 s1XXXXXXX kernel: sd 1:0:0:0: SCSI error: return code = 0x00040000
.
.
.
Jan 16 21:25:01 s1XXXXXXX /usr/sbin/cron[28058]: (mailman) CMD (/usr/bin/python -S /usr/lib/mailman/cron/gate_news)
Jan 16 21:26:05 s1XXXXXXX shutdown[28060]: shutting down for system reboot
Jan 16 21:26:05 s1XXXXXXX init: Switching to runlevel: 6
Jan 16 21:26:12 s1XXXXXXX xinetd[24129]: Exiting...
Jan 16 21:26:12 s1XXXXXXX qmail: 1232137572.656558 status: exiting
Jan 16 21:26:12 s1XXXXXXX sshd[3840]: Received signal 15; terminating.
Jan 16 21:26:14 s1XXXXXXX kernel: Kernel logging (proc) stopped.
Jan 16 21:26:14 s1XXXXXXX kernel: Kernel log daemon terminating.
Jan 16 21:26:15 s1XXXXXXX spamd[19653]: spamd: server killed by SIGTERM, shutting down
Jan 16 21:26:15 s1XXXXXXX syslog-ng[4389]: syslog-ng version 1.6.11 going down

----------------------------------------------

Code: Select all

var/log/mail.info

Code: Select all

Jan 16 15:12:22 s1XXXXXXX pop3d: IMAP connect from @ [80.187.102.228]INFO: LOGIN, user=info@domain.de, ip=[80.187.102.228]
Jan 16 15:12:38 s1XXXXXXX pop3d: IMAP connect from @ [84.184.29.74]INFO: LOGIN,user=a.probst@domain.de, ip=[84.184.29.74]
Jan 16 15:12:39 s1XXXXXXX pop3d: IMAP connect from @ [84.184.29.74]INFO: LOGIN,user=info@domain.de, ip=[84.184.29.74]
Jan 16 15:12:39 s1XXXXXXX pop3d: IMAP connect from @ [84.184.29.74]INFO: LOGIN,user=r.bachmann@domain.de, ip=[84.184.29.74]
Jan 16 15:12:39 s1XXXXXXX pop3d: IMAP connect from @ [84.184.29.74]INFO: LOGIN,user=w.lotz@domain.de, ip=[84.184.29.74]
Jan 16 15:12:52 s1XXXXXXX pop3d: IMAP connect from @ [82.119.160.28]INFO: LOGIN, user=service@domain.de, ip=[82.119.160.28]
Jan 16 15:12:57 s1XXXXXXX qmail: 1232115177.527729 new msg 12624216
Jan 16 15:12:57 s1XXXXXXX qmail: 1232115177.527991 info msg 12624216: bytes 17673 from <vkyrx@borg.phx.mcd.mot.com> qp 26838 uid 2020
Jan 16 15:12:57 s1XXXXXXX qmail: 1232115177.533589 starting delivery 5512: msg 12624216 to local 3-info@domain.at
Jan 16 15:12:57 s1XXXXXXX qmail: 1232115177.533808 status: local 1/10 remote 0/20
Jan 16 15:12:57 s1XXXXXXX qmail: 1232115177.550848 delivery 5512: success: did_0+0+2/
Jan 16 15:12:57 s1XXXXXXX qmail: 1232115177.550967 status: local 0/10 remote 0/20
Jan 16 15:12:57 s1XXXXXXX qmail: 1232115177.551019 end msg 12624216
Jan 16 21:26:12 s1XXXXXXX qmail: 1232137572.656558 status: exiting
Jan 16 21:26:15 s1XXXXXXX spamd[19653]: spamd: server killed by SIGTERM, shutting down
----------------------------------------------

Code: Select all

var/log/warn

Code: Select all

Jan 16 15:12:01 s1XXXXXXX relaylock: /var/qmail/bin/relaylock: mail from 195.95.151.15:1815 (customer-eastnet-195-95-151-15.rise.com.ua)
Jan 16 15:12:02 s1XXXXXXX relaylock: /var/qmail/bin/relaylock: mail from 195.95.151.15:1822 (customer-eastnet-195-95-151-15.rise.com.ua)
Jan 16 15:12:38 s1XXXXXXX pop3d: 1232115158.732752 LOGOUT, user=a.probst@domain.de, ip=[84.184.29.74], top=0, retr=0, time=0, rcvd=12, sent=39, ma
ildir=/var/qmail/mailnames/domain.de/a.probst/Maildir
Jan 16 15:12:39 s1XXXXXXX pop3d: 1232115159.125128 LOGOUT, user=info@domain.de, ip=[84.184.29.74], top=0, retr=0, time=0, rcvd=12, sent=39, maildi
r=/var/qmail/mailnames/domain.de/info/Maildir
Jan 16 15:12:39 s1XXXXXXX pop3d: 1232115159.517195 LOGOUT, user=r.bachmann@domain.de, ip=[84.184.29.74], top=0, retr=0, time=0, rcvd=12, sent=39,
maildir=/var/qmail/mailnames/domain.de/r.bachmann/Maildir
Jan 16 15:12:39 s1XXXXXXX pop3d: 1232115159.909603 LOGOUT, user=w.lotz@domain.de, ip=[84.184.29.74], top=0, retr=0, time=0, rcvd=12, sent=39, mail
dir=/var/qmail/mailnames/domain.de/w.lotz/Maildir
Jan 16 15:12:52 s1XXXXXXX relaylock: /var/qmail/bin/relaylock: mail from 83.170.
209.154:59071 (ll-154.209.170.83.dp.sovam.net.ua)
Jan 16 15:12:52 s1XXXXXXX pop3d: 1232115172.816027 LOGOUT, user=service@domain.de, ip=[82.119.160.28], top=0, retr=0, time=0, rcvd=12, sent=39, maildi
r=/var/qmail/mailnames/domain.de/service/Maildir
Jan 16 15:17:21 s1XXXXXXX pop3d: 1232115441.302431 TIMEOUT, user=info@domain.de, ip=[80.187.102.228], top=0, retr=0, time=301, rcvd=12, sent=44, mail
dir=/var/qmail/mailnames/domain.de/info/Maildir
Jan 16 15:17:23 s1XXXXXXX pop3d: 1232115443.302499 TIMEOUT, user=reservierung@domain.de, ip=[80.187.102.228], top=0, retr=0, time=301, rcvd=12, sent=3
8, maildir=/var/qmail/mailnames/domain.de/reservierung/Maildir
Jan 16 15:17:23 s1XXXXXXX pop3d: 1232115443.490494 TIMEOUT, user=info@domain.de, ip=[80.187.102.228], top=0, retr=0, time=301, rcvd=12, sent=41, maild
ir=/var/qmail/mailnames/domain.de/info/Maildir
Jan 16 15:17:23 s1XXXXXXX pop3d: 1232115443.542491 TIMEOUT, user=info@domain.de, ip=[80.187.102.228], top=0, retr=0, time=301, rcvd=12, sent=45, mail
dir=/var/qmail/mailnames/domain.de/info/Maildir
Jan 16 19:01:07 s1XXXXXXX kernel: end_request: I/O error, dev sdb, sector 0
Jan 16 19:01:07 s1XXXXXXX kernel: Buffer I/O error on device sdb, logical block 0
Jan 16 19:01:07 s1XXXXXXX kernel: Buffer I/O error on device sdb, logical block 1
Jan 16 19:01:07 s1XXXXXXX kernel: Buffer I/O error on device sdb, logical block 2
Jan 16 19:01:07 s1XXXXXXX kernel: Buffer I/O error on device sdb, logical block 3
Jan 16 19:01:07 s1XXXXXXX kernel: end_request: I/O error, dev sdb, sector 0
Jan 16 19:01:07 s1XXXXXXX kernel: Buffer I/O error on device sdb, logical block 
Jan 16 19:01:08 s1XXXXXXX kernel: end_request: I/O error, dev sdb, sector 312581744
Jan 16 19:01:08 s1XXXXXXX kernel: end_request: I/O error, dev sdb, sector 312581744
Jan 16 19:01:08 s1XXXXXXX kernel: end_request: I/O error, dev sdb, sector 312581552
Jan 16 19:01:08 s1XXXXXXX kernel: end_request: I/O error, dev sdb, sector 312581552
Jan 16 19:01:08 s1XXXXXXX kernel: end_request: I/O error, dev sdb, sector 312581552
Jan 16 19:01:08 s1XXXXXXX kernel: end_request: I/O error, dev sdb, sector 312581792
Jan 16 19:01:08 s1XXXXXXX kernel: end_request: I/O error, dev sdb, sector 312581408
Jan 16 19:01:08 s1XXXXXXX kernel: end_request: I/O error, dev sdb, sector 312581408
Jan 16 19:01:08 s1XXXXXXX kernel: end_request: I/O error, dev sdb, sector 312581072
Jan 16 19:01:08 s1XXXXXXX kernel: end_request: I/O error, dev sdb, sector 312581072
Jan 16 19:01:08 s1XXXXXXX kernel: end_request: I/O error, dev sdb, sector 312581800
Jan 16 19:01:08 s1XXXXXXX kernel: end_request: I/O error, dev sdb, sector 312581800
Jan 16 21:26:12 s1XXXXXXX xinetd[24129]: Exiting...
----------------------------------------------

Code: Select all

var/log/mail.err

Code: Select all

Jan 16 15:11:37 s1XXXXXXX pop3d: 1232115097.927307 LOGOUT, user=r.bachmann@domain.de, ip=[84.184.29.74], top=0, retr=0, time=0, rcvd=12, sent=39,
maildir=/var/qmail/mailnames/domain.de/r.bachmann/Maildir
Jan 16 15:11:38 s1XXXXXXX pop3d: 1232115098.319406 LOGOUT, user=w.lotz@domain.de, ip=[84.184.29.74], top=0, retr=0, time=0, rcvd=12, sent=39, mail
dir=/var/qmail/mailnames/domain.de/w.lotz/Maildir
Jan 16 15:11:55 s1XXXXXXX pop3d: 1232115115.713789 LOGOUT, user=info-k@domain.de, ip=[91.0.49.8], top=0, retr=0, time=0, rcvd=12, sent=39, maildir=/var/qmai
l/mailnames/domain.de/info-k/Maildir
Jan 16 15:12:38 s1XXXXXXX pop3d: 1232115158.732752 LOGOUT, user=a.probst@domain.de, ip=[84.184.29.74], top=0, retr=0, time=0, rcvd=12, sent=39, ma
ildir=/var/qmail/mailnames/domain.de/a.probst/Maildir
Jan 16 15:12:39 s1XXXXXXX pop3d: 1232115159.125128 LOGOUT, user=info@domain.de, ip=[84.184.29.74], top=0, retr=0, time=0, rcvd=12, sent=39, maildi
r=/var/qmail/mailnames/domain.de/info/Maildir
Jan 16 15:12:39 s1XXXXXXX pop3d: 1232115159.517195 LOGOUT, user=r.bachmann@domain.de, ip=[84.184.29.74], top=0, retr=0, time=0, rcvd=12, sent=39,
maildir=/var/qmail/mailnames/domain.de/r.bachmann/Maildir
Jan 16 15:12:39 s1XXXXXXX pop3d: 1232115159.909603 LOGOUT, user=w.lotz@domain.de, ip=[84.184.29.74], top=0, retr=0, time=0, rcvd=12, sent=39, mail
dir=/var/qmail/mailnames/domain.de/w.lotz/Maildir
Jan 16 15:12:52 s1XXXXXXX pop3d: 1232115172.816027 LOGOUT, user=service@domain.de, ip=[82.119.160.28], top=0, retr=0, time=0, rcvd=12, sent=39, maildi
r=/var/qmail/mailnames/domain.de/service/Maildir
Jan 16 15:17:21 s1XXXXXXX pop3d: 1232115441.302431 TIMEOUT, user=info@domain.de, ip=[80.187.102.228], top=0, retr=0, time=301, rcvd=12, sent=44, mail
dir=/var/qmail/mailnames/domain.de/info/Maildir
Jan 16 15:17:23 s1XXXXXXX pop3d: 1232115443.302499 TIMEOUT, user=reservierung@domain.de, ip=[80.187.102.228], top=0, retr=0, time=301, rcvd=12, sent=3
8, maildir=/var/qmail/mailnames/domain.de/reservierung/Maildir
Jan 16 15:17:23 s1XXXXXXX pop3d: 1232115443.490494 TIMEOUT, user=info@domain.de, ip=[80.187.102.228], top=0, retr=0, time=301, rcvd=12, sent=41, maild
ir=/var/qmail/mailnames/domain.de/info/Maildir
Jan 16 15:17:23 s1XXXXXXX pop3d: 1232115443.542491 TIMEOUT, user=info@domain.de, ip=[80.187.102.228], top=0, retr=0, time=301, rcvd=12, sent=45, mail
dir=/var/qmail/mailnames/domain.de/info/Maildir
----------------------------------------------

Code: Select all

var/log/mail.warn

Code: Select all

Jan 16 15:04:02 s1XXXXXXX smtp_auth: smtp_auth: SMTP user info-k@domain.de : logged in from (null)@p5b003108.dip0.t-ipconnect.de [91.0.49.8]
Jan 16 15:06:22 s1XXXXXXX relaylock: /var/qmail/bin/relaylock: mail from 201.250.47.34:2523 (201-250-47-34.speedy.com.ar)
Jan 16 15:06:58 s1XXXXXXX relaylock: /var/qmail/bin/relaylock: mail from 91.0.49.8:63843 (p5b003108.dip0.t-ipconnect.de)
Jan 16 15:06:58 s1XXXXXXX smtp_auth: SMTP connect from (null)@p5b003108.dip0.t-ipconnect.de [91.0.49.8]
Jan 16 15:06:58 s1XXXXXXX smtp_auth: smtp_auth: SMTP user info-k@domain.de : logged in from (null)@p5b003108.dip0.t-ipconnect.de [91.0.49.8]
Jan 16 15:07:14 s1XXXXXXX relaylock: /var/qmail/bin/relaylock: mail from 194.0.130.3:46085 (colombo.bimar.com.tr)
Jan 16 15:11:56 s1XXXXXXX relaylock: /var/qmail/bin/relaylock: mail from 195.95.151.15:1705 (customer-eastnet-195-95-151-15.rise.com.ua)
Jan 16 15:11:56 s1XXXXXXX relaylock: /var/qmail/bin/relaylock: mail from 195.95.151.15:1704 (customer-eastnet-195-95-151-15.rise.com.ua)
Jan 16 15:11:56 s1XXXXXXX relaylock: /var/qmail/bin/relaylock: mail from 195.95.151.15:1702 (customer-eastnet-195-95-151-15.rise.com.ua)
Jan 16 15:11:56 s1XXXXXXX relaylock: /var/qmail/bin/relaylock: mail from 195.95.151.15:1701 (customer-eastnet-195-95-151-15.rise.com.ua)
Jan 16 15:11:59 s1XXXXXXX relaylock: /var/qmail/bin/relaylock: mail from 195.95.151.15:1793 (customer-eastnet-195-95-151-15.rise.com.ua)
Jan 16 15:12:00 s1XXXXXXX relaylock: /var/qmail/bin/relaylock: mail from 195.95.151.15:1792 (customer-eastnet-195-95-151-15.rise.com.ua)
Jan 16 15:12:01 s1XXXXXXX relaylock: /var/qmail/bin/relaylock: mail from 195.95.151.15:1811 (customer-eastnet-195-95-151-15.rise.com.ua)
Jan 16 15:12:01 s1XXXXXXX relaylock: /var/qmail/bin/relaylock: mail from 195.95.151.15:1815 (customer-eastnet-195-95-151-15.rise.com.ua)
Jan 16 15:12:02 s1XXXXXXX relaylock: /var/qmail/bin/relaylock: mail from 195.95.151.15:1822 (customer-eastnet-195-95-151-15.rise.com.ua)
Jan 16 15:12:52 s1XXXXXXX relaylock: /var/qmail/bin/relaylock: mail from 83.170.209.154:59071 (ll-154.209.170.83.dp.socd .vam.net.ua)
----------------------------------------------

Code: Select all

var/log/apache2/access_log

Code: Select all

127.0.0.1 - - [16/Jan/2009:15:06:41 +0100] "GET / HTTP/1.0" 200 262 "-" "Apache/2.2.3 (Linux/SUSE) (internal dummy connection)"
127.0.0.1 - - [16/Jan/2009:15:06:42 +0100] "GET / HTTP/1.0" 200 262 "-" "Apache/2.2.3 (Linux/SUSE) (internal dummy connection)"
127.0.0.1 - - [16/Jan/2009:15:06:44 +0100] "GET / HTTP/1.0" 200 262 "-" "Apache/2.2.3 (Linux/SUSE) (internal dummy connection)"
127.0.0.1 - - [16/Jan/2009:15:06:45 +0100] "GET / HTTP/1.0" 200 262 "-" "Apache/2.2.3 (Linux/SUSE) (internal dummy connection)"
77.23.235.12 - - [16/Jan/2009:15:07:02 +0100] "GET /cms/website.php?id=/de/seite.htm HTTP/1.1" 301 371 "http://www.trivago.de/28613/restaurant-gaststaette/s/bewertung-o1" "Opera/9.20 WindowsNT 5.1; U; de)"
::1 - - [16/Jan/2009:23:46:09 +0100] "GET / HTTP/1.0" 200 262 "-" "Apache/2.2.3 (Linux/SUSE) (internal dummy connection)"
::1 - - [16/Jan/2009:23:46:11 +0100] "GET / HTTP/1.0" 200 262 "-" "Apache/2.2.3 (Linux/SUSE) (internal dummy connection)"
----------------------------------------------

Code: Select all

var/log/apache2/error_log

Code: Select all

[Fri Jan 16 04:03:51 2009] [error] [client 66.249.73.8] File does not exist: /srv/www/vhosts/default/htdocs/robots.txt
[Fri Jan 16 13:59:15 2009] [error] [client 195.70.61.122] client sent HTTP/1.1 request without hostname (see RFC2616 section 14.23): /w00tw00t.at.ISC.SANS.DFind:)
[Fri Jan 16 21:26:30 2009] [warn] child process 26244 still did not exit, sending a SIGTERM
[Fri Jan 16 21:26:30 2009] [warn] child process 25045 still did not exit, sending a SIGTERM
[Fri Jan 16 21:26:30 2009] [warn] child process 25249 still did not exit, sending a SIGTERM
.
.
.
----------------------------------------------

Code: Select all

/etc/lilo.conf

Code: Select all

# Modified by YaST2. Last modification on Tue Jan 29 00:25:01 CET 2008
boot = /dev/sda
root = /dev/md1
install = /boot/boot.b
vga = normal
timeout = 60
prompt
lba32
read-only
default = Linux
serial = 0,57600n8
append = "console=ttyS0,57600 console=tty0"

image = /boot/vmlinuz-2.6.18.8-0.7-default
###Don't change this comment - YaST2 identifier: Original name: linux###
    label = Linux
    append = " console=tty0 console=ttyS0,57600 panic=30"
    initrd = /boot/initrd-2.6.18.8-0.7-default
    root = /dev/md1

image = /boot/vmlinuz-2.6.18.8-0.7-default
###Don't change this comment - YaST2 identifier: Original name: failsafe###
    label = Failsafe
    append = "showopts ide=nodma apm=off acpi=off noresume edd=off 3"
    initrd = /boot/initrd-2.6.18.8-0.7-default
    root = /dev/md1


image = /boot/vmlinuz
    label = lxser
    append = " console=tty0 console=ttyS0,57600 panic=30"


image = /boot/vmlinuz
    label = lx
----------------------------------------------

Code: Select all

/proc/partitions

Code: Select all

major minor  #blocks  name

   8     0  156290904 sda
   8     1     987966 sda1
   8     2    1959930 sda2
   8     4          1 sda4
   8     5    4891761 sda5
   8     6    4891761 sda6
   8     7   19543041 sda7
   8     8  124013736 sda8
   8    16  156290904 sdb
   8    17     987966 sdb1
   8    18    1959930 sdb2
   8    20          1 sdb4
   8    21    4891761 sdb5
   8    22    4891761 sdb6
   8    23   19543041 sdb7
   8    24  124013736 sdb8
   9     8  124013632 md8
   9     7   19542976 md7
   9     6    4891648 md6
   9     5    4891648 md5
   9     1     987840 md1
----------------------------------------------

Code: Select all

/etc/fstab

Code: Select all

/dev/md1        /               ext3    defaults                1 1
/dev/sda2       swap            swap    sw
/dev/sdb2       swap            swap    sw
/dev/md5        /usr            xfs     defaults                1 2
/dev/md6        /var            xfs     defaults,usrquota       1 2
/dev/md7        /home           xfs     defaults,usrquota       1 2
/dev/md8        /srv            xfs     defaults,usrquota       1 2

proc            /proc           proc    defaults                0 0
sysfs           /sys            sysfs   noauto                  0 0
none            /tmp            tmpfs   defaults                0 0
----------------------------------------------
REBOOT UNTER BEIBEHALTUNG RESCUE MODUS:

Code: Select all

shutdown -rn now

Code: Select all

sending all processes powernowd[1713]: segfault at 0 ip 00007f5039b42f04 sp 00007fff41e19498 error 4 in libc-2.3.2.so[7f5039ac5000+122000]
the TERM signal...
shumd: md7 in immediate safe mode
md: md8 in immediate safe mode
md: md5 in immediate safe mode
md: md1 in immediate safe mode
md: md6 in immediate safe mode
md: stopping all md devices.
md: md5 switched to read-only mode.
md: md6 switched to read-only mode.
md: md7 switched to read-only mode.
md: md8 switched to read-only mode.
kvm: exiting hardware virtualization
sd 1:0:0:0: [sdb] Synchronizing SCSI cache
sd 0:0:0:0: [sda] Synchronizing SCSI cache
forcedeth 0000:00:14.0: PCI INT A disabled
Restarting system.
machine restart
.
.
.
i2c /dev entries driver
i2c-adapter i2c-0: nForce2 SMBus adapter at 0x88c0
i2c-adapter i2c-1: nForce2 SMBus adapter at 0x8880
md: linear personality registered for level -1
md: raid0 personality registered for level 0
md: raid1 personality registered for level 1
md: raid10 personality registered for level 10
raid6: int64x1   1885 MB/s
raid6: int64x2   2280 MB/s
raid6: int64x4   2456 MB/s
raid6: int64x8   1713 MB/s
raid6: sse2x1    2966 MB/s
raid6: sse2x2    3885 MB/s
raid6: sse2x4    3987 MB/s
raid6: using algorithm sse2x4 (3987 MB/s)
md: raid6 personality registered for level 6
md: raid5 personality registered for level 5
md: raid4 personality registered for level 4
md: faulty personality registered for level -5
device-mapper: ioctl: 4.14.0-ioctl (2008-04-23) initialised: dm-devel@redhat.com
usbcore: registered new interface driver usbhid
usbhid: v2.6:USB HID core driver
Netfilter messages via NETLINK v0.30.
nf_conntrack version 0.5.0 (8192 buckets, 32768 max)
CONFIG_NF_CT_ACCT is deprecated and will be removed soon. Plase use
nf_conntrack.acct=1 kernel paramater, acct=1 nf_conntrack module option or
sysctl net.netfilter.nf_conntrack_acct=1 to enable it.
ctnetlink v0.93: registering with nfnetlink.
ip_tables: (C) 2000-2006 Netfilter Core Team
ClusterIP Version 0.8 loaded successfully
arp_tables: (C) 2002 David S. Miller
TCP cubic registered
NET: Registered protocol family 10
lo: Disabled Privacy Extensions
ip6_tables: (C) 2000-2006 Netfilter Core Team
IPv6 over IPv4 tunneling driver
sit0: Disabled Privacy Extensions
NET: Registered protocol family 17
NET: Registered protocol family 15
RPC: Registered udp transport module.
RPC: Registered tcp transport module.
powernow-k8: Found 1 AMD Athlon(tm) 64 X2 Dual Core Processor 4000+ processors (2 cpu cores) (version 2.20.00)
powernow-k8:    0 : fid 0xd (2100 MHz), vid 0xc
powernow-k8:    1 : fid 0xc (2000 MHz), vid 0xd
powernow-k8:    2 : fid 0xa (1800 MHz), vid 0xf
powernow-k8:    3 : fid 0x2 (1000 MHz), vid 0x12
md: Autodetecting RAID arrays.
md: Scanned 10 and added 10 devices.
md: autorun ...
md: considering sdb8 ...
md:  adding sdb8 ...
md: sdb7 has different UUID to sdb8
md: sdb6 has different UUID to sdb8
md: sdb5 has different UUID to sdb8
md: sdb1 has different UUID to sdb8
md:  adding sda8 ...
md: sda7 has different UUID to sdb8
md: sda6 has different UUID to sdb8
md: sda5 has different UUID to sdb8
md: sda1 has different UUID to sdb8
md: created md8
md: bind<sda8>
md: bind<sdb8>
md: running: <sdb8><sda8>
md: kicking non-fresh sdb8 from array!
md: unbind<sdb8>
md: export_rdev(sdb8)
raid1: raid set md8 active with 1 out of 2 mirrors
md: considering sdb7 ...
md:  adding sdb7 ...
md: sdb6 has different UUID to sdb7
md: sdb5 has different UUID to sdb7
md: sdb1 has different UUID to sdb7
md:  adding sda7 ...
md: sda6 has different UUID to sdb7
md: sda5 has different UUID to sdb7
md: sda1 has different UUID to sdb7
md: created md7
md: bind<sda7>
md: bind<sdb7>
md: running: <sdb7><sda7>
md: kicking non-fresh sdb7 from array!
md: unbind<sdb7>
md: export_rdev(sdb7)
raid1: raid set md7 active with 1 out of 2 mirrors
md: considering sdb6 ...
md:  adding sdb6 ...
md: sdb5 has different UUID to sdb6
md: sdb1 has different UUID to sdb6
md:  adding sda6 ...
md: sda5 has different UUID to sdb6
md: sda1 has different UUID to sdb6
md: created md6
md: bind<sda6>
md: bind<sdb6>
md: running: <sdb6><sda6>
md: kicking non-fresh sdb6 from array!
md: unbind<sdb6>
md: export_rdev(sdb6)
raid1: raid set md6 active with 1 out of 2 mirrors
md: considering sdb5 ...
md:  adding sdb5 ...
md: sdb1 has different UUID to sdb5
md:  adding sda5 ...
md: sda1 has different UUID to sdb5
md: created md5
md: bind<sda5>
md: bind<sdb5>
md: running: <sdb5><sda5>
md: kicking non-fresh sdb5 from array!
md: unbind<sdb5>
md: export_rdev(sdb5)
[b]raid1: raid set md5 active with 1 out of 2 mirrors
md: considering sdb1 ...
md:  adding sdb1 ...
md:  adding sda1 ...
md: created md1
md: bind<sda1>
md: bind<sdb1>
md: running: <sdb1><sda1>
md: kicking non-fresh sdb1 from array!
md: unbind<sdb1>
md: export_rdev(sdb1)
raid1: raid set md1 active with 1 out of 2 mirrors[/b]
md: ... autorun DONE.
RAMDISK: Compressed image found at block 0
EXT4-fs warning (device ram0): ext4_fill_super: extents feature not enabled on this filesystem, use tune2fs.

EXT4-fs: ram0: not marked OK to use with test code.
VFS: Mounted root (ext2 filesystem).
Freeing unused kernel memory: 448k freed
Write protecting the kernel read-only data: 6476k
INIT: version 2.86 booting
Setting parameters of disc: (none).
Activating swap.
System time was Sat Jan 17 11:15:20 UTC 2009.
Setting the System Clock using the Hardware Clock as reference...
System Clock set. System local time is now Sat Jan 17 11:15:22 UTC 2009.
Cleaning up ifupdown...done.
Not running depmod because /lib/modules/2.6.27.7-20081121a/ is not writeable.
Loading modules...
All modules loaded.
FATAL: Could not load /lib/modules/2.6.27.7-20081121a/modules.dep: No such file or directory
Creating device-mapper devices...done.
Starting raid devices: done.
Setting up LVM Volume Groups...
  Reading all physical volumes.  This may take a while...
  No volume groups found
  No volume groups found
  No volume groups found
Checking all file systems...
fsck 1.37 (21-Mar-2005)
Setting kernel variables ...
... done.
Mounting local filesystems...
Cleaning /tmp /var/run /var/lock.
Setting up networking...done.
Setting up IP spoofing protection: rp_filter.
Configuring network interfaces...Internet Systems Consortium DHCP Client V3.0.1
Copyright 2004 Internet Systems Consortium.
All rights reserved.
For info, please visit http://www.isc.org/products/DHCP

sit0: unknown hardware address type 776
sit0: unknown hardware address type 776
Listening on LPF/eth0/00:19:99:07:c2:02
Sending on   LPF/eth0/00:19:99:07:c2:02
Sending on   Socket/fallback
DHCPDISCOVER on eth0 to 255.255.255.255 port 67 interval 2
DHCPOFFER from 99.999.999.999
DHCPREQUEST on eth0 to 255.255.255.255 port 67
DHCPACK from 99.999.999.999
bound to 99.999.999.999 -- renewal in 72082 seconds.
done.

Setting the System Clock using the Hardware Clock as reference...
System Clock set. Local time: Sat Jan 17 12:15:26 CET 2009

Running ntpdate to synchronize clock.
Initializing random number generator...done.
INIT: Entering runlevel: 2
Starting system log daemon: syslogd.
Starting kernel log daemon: klogd.
Starting MTA: /usr/sbin/update-exim4.conf: Error, no /etc/exim4/conf.d, exiting.
Starting internet superserver: inetd.
Starting openntpd: ntpd.
Starting powernowd: powernowd.
Not starting S.M.A.R.T. daemon smartd, disabled via /etc/default/smartmontools
Starting OpenBSD Secure Shell server: sshd.
sadc not enabled in /etc/default/sysstat, not starting.
Starting NTP server: ntpd/usr/sbin/ntpd: invalid option -- p
usage: ntpd [-dSs] [-f file]
.
Starting RAID monitor daemon: mdadm -F.
Starting periodic command scheduler: cron.

Debian GNU/Linux 3.1 rescue ttyS0

rescue login: Clocksource tsc unstable (delta = -71495736 ns)
----------------------------------------------
REBOOT IN NORMALEN MODUS:

Code: Select all

shutdown -rn now

Code: Select all

shutdown: sendinpowernowd[1713]: segfault at 0 ip 00007ff73ccd2f04 sp 00007fff44fa7628 error 4 in libc-2.3.2.so[7ff73cc55000+122000]
g all processes the TERM signal...
shutdown: sendinmd: md8 in immediate safe mode
md: md1 in immediate safe mode
md: md5 in immediate safe mode
md: md6 in immediate safe mode
md: md7 in immediate safe mode
md: stopping all md devices.
md: md1 switched to read-only mode.
md: md5 switched to read-only mode.
md: md6 switched to read-only mode.
md: md7 switched to read-only mode.
md: md8 switched to read-only mode.
kvm: exiting hardware virtualization
sd 1:0:0:0: [sdb] Synchronizing SCSI cache
sd 0:0:0:0: [sda] Synchronizing SCSI cache
forcedeth 0000:00:14.0: PCI INT A disabled
Restarting system.
machine restart

LILO 22.7 boot:
Loading Linux............................................................................................
BIOS data check successful
Bootdata ok (command line is auto BOOT_IMAGE=Linux ro root=901 console=tty0 console=ttyS0,57600 panic=30)
Linux version 2.6.18.8-0.7-default (geeko@buildhost) (gcc version 4.1.2 20061115 (prerelease) (SUSE Linux)) #1 SMP Tue Oct 2 17:21:08 UTC 2007
BIOS-provided physical RAM map:
 BIOS-e820: 0000000000000000 - 000000000009e000 (usable)
 BIOS-e820: 000000000009e000 - 00000000000a0000 (reserved)
 BIOS-e820: 00000000000d0000 - 0000000000100000 (reserved)
 BIOS-e820: 0000000000100000 - 000000003df10000 (usable)
 BIOS-e820: 000000003df10000 - 000000003df16000 (ACPI data)
 BIOS-e820: 000000003df16000 - 000000003df80000 (ACPI NVS)
 BIOS-e820: 000000003df80000 - 0000000040000000 (reserved)
 BIOS-e820: 00000000fc000000 - 00000000fe000000 (reserved)
 BIOS-e820: 00000000fec00000 - 00000000fec10000 (reserved)
 BIOS-e820: 00000000fee00000 - 00000000fee01000 (reserved)
 BIOS-e820: 00000000fff80000 - 0000000100000000 (reserved)
DMI present.
Scanning NUMA topology in Northbridge 24
Number of nodes 1
Node 0 MemBase 0000000000000000 Limit 000000003df10000
Using node hash shift of 63
Bootmem setup node 0 0000000000000000-000000003df10000
Nvidia board detected. Ignoring ACPI timer override.
If you got timer trouble try acpi_use_timer_override
ACPI: PM-Timer IO Port: 0x1008
ACPI: LAPIC (acpi_id[0x00] lapic_id[0x00] enabled)
Processor #0 15:11 APIC version 16
ACPI: LAPIC (acpi_id[0x01] lapic_id[0x01] enabled)
Processor #1 15:11 APIC version 16
ACPI: LAPIC_NMI (acpi_id[0x00] high edge lint[0x1])
ACPI: LAPIC_NMI (acpi_id[0x01] high edge lint[0x1])
ACPI: IOAPIC (id[0x02] address[0xfec00000] gsi_base[0])
IOAPIC[0]: apic_id 2, version 17, address 0xfec00000, GSI 0-23
Setting APIC routing to physical flat
Using ACPI (MADT) for SMP configuration information
Allocating PCI resources starting at 50000000 (gap: 40000000:bc000000)
SMP: Allowing 2 CPUs, 0 hotplug CPUs
Built 1 zonelists.  Total pages: 248320
Kernel command line: auto BOOT_IMAGE=Linux ro root=901 console=tty0 console=ttyS0,57600 panic=30
Initializing CPU#0
PID hash table entries: 4096 (order: 12, 32768 bytes)
Disabling vsyscall due to use of PM timer
time.c: Using 3.579545 MHz WALL PM GTOD PM timer.
time.c: Detected 2109.639 MHz processor.
Console: colour VGA+ 80x25
Dentry cache hash table entries: 131072 (order: 8, 1048576 bytes)
Inode-cache hash table entries: 65536 (order: 7, 524288 bytes)
Checking aperture...
CPU 0: aperture @ 229a000000 size 32 MB
Aperture too small (32 MB)
No AGP bridge found
Memory: 991512k/1014848k available (1915k kernel code, 22944k reserved, 1282k data, 188k init)
Calibrating delay using timer specific routine.. 4223.87 BogoMIPS (lpj=8447756)
Security Framework v1.0.0 initialized
Mount-cache hash table entries: 256
CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line)
CPU: L2 Cache: 512K (64 bytes/line)
CPU 0/0 -> Node 0
CPU: Physical Processor ID: 0
CPU: Processor Core ID: 0
SMP alternatives: switching to UP code
checking if image is initramfs... it is
Freeing initrd memory: 3105k freed
ACPI: Core revision 20060707
Using local APIC timer interrupts.
result 12557392
Detected 12.557 MHz APIC timer.
SMP alternatives: switching to SMP code
Booting processor 1/2 APIC 0x1
Initializing CPU#1
Calibrating delay using timer specific routine.. 4219.49 BogoMIPS (lpj=8438993)
CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line)
CPU: L2 Cache: 512K (64 bytes/line)
CPU 1/1 -> Node 0
CPU: Physical Processor ID: 0
CPU: Processor Core ID: 1
AMD Athlon(tm) 64 X2 Dual Core Processor 4000+ stepping 01
CPU 1: Syncing TSC to CPU 0.
CPU 1: synchronized TSC with CPU 0 (last diff 0 cycles, maxerr 559 cycles)
Brought up 2 CPUs
testing NMI watchdog ... OK.
migration_cost=338
NET: Registered protocol family 16
ACPI: bus type pci registered
PCI: Using MMCONFIG at fc000000
PCI: No mmconfig possible on device 0:18
ACPI: Interpreter enabled
ACPI: Using IOAPIC for interrupt routing
ACPI: PCI Root Bridge [PCI0] (0000:00)
PCI: Transparent bridge - 0000:00:10.0
ACPI: Device [TPM] status [00000008]: functional but not present; setting present
ACPI: PCI Interrupt Link [LNKA] (IRQs 5 7 10 11 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LNKB] (IRQs 5 7 10 11 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LNKC] (IRQs 5 7 10 11 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LNKD] (IRQs 5 7 10 11 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LNKE] (IRQs 16 17 18 19 20 21 22 23) *0, disabled.
ACPI: PCI Interrupt Link [LNKF] (IRQs 16 17 18 19 20 21 22 23) *0, disabled.
ACPI: PCI Interrupt Link [LNKG] (IRQs 16 17 18 19 20 21 22 23) *10
ACPI: PCI Interrupt Link [LNKH] (IRQs 16 17 18 19 20 21 22 23) *0, disabled.
ACPI: PCI Interrupt Link [LNKI] (IRQs 16 17 18 19 20 21 22 23) *7
ACPI: PCI Interrupt Link [LNKJ] (IRQs 16 17 18 19 20 21 22 23) *11
ACPI: PCI Interrupt Link [LNKK] (IRQs 16 17 18 19 20 21 22 23) *10
ACPI: PCI Interrupt Link [LNKL] (IRQs 16 17 18 19 20 21 22 23) *11
ACPI: PCI Interrupt Link [LNKM] (IRQs 16 17 18 19 20 21 22 23) *0, disabled.
ACPI: PCI Interrupt Link [LNKN] (IRQs 16 17 18 19 20 21 22 23) *5
ACPI: PCI Interrupt Link [LNKO] (IRQs 16 17 18 19 20 21 22 23) *0, disabled.
ACPI: PCI Interrupt Link [LNKP] (IRQs 16 17 18 19 20 21 22 23) *0, disabled.
ACPI: Device [FDC] status [00000008]: functional but not present; setting present
ACPI: Device [LPT] status [00000008]: functional but not present; setting present
ACPI: Device [ECP] status [00000008]: functional but not present; setting present
ACPI: Device [COM2] status [00000008]: functional but not present; setting present
PCI: Using ACPI for IRQ routing
PCI: If a device doesn't work, try "pci=routeirq".  If it helps, post a report
PCI-DMA: Disabling IOMMU.
PCI: Bridge: 0000:00:02.0
  IO window: disabled.
  MEM window: disabled.
  PREFETCH window: disabled.
PCI: Bridge: 0000:00:03.0
  IO window: disabled.
  MEM window: disabled.
  PREFETCH window: disabled.
PCI: Bridge: 0000:00:10.0
  IO window: disabled.
  MEM window: disabled.
  PREFETCH window: disabled.
NET: Registered protocol family 2
IP route cache hash table entries: 32768 (order: 6, 262144 bytes)
TCP established hash table entries: 131072 (order: 9, 2097152 bytes)
TCP bind hash table entries: 65536 (order: 8, 1048576 bytes)
TCP: Hash tables configured (established 131072 bind 65536)
TCP reno registered
Simple Boot Flag at 0x36 set to 0x80
audit: initializing netlink socket (disabled)
audit(1232191474.256:1): initialized
Total HugeTLB memory allocated, 0
VFS: Disk quotas dquot_6.5.1
Dquot-cache hash table entries: 512 (order 0, 4096 bytes)
Initializing Cryptographic API
io scheduler noop registered
io scheduler anticipatory registered
io scheduler deadline registered
io scheduler cfq registered (default)
pcie_portdrv_probe->Dev[02fc:10de] has invalid IRQ. Check vendor BIOS
assign_interrupt_mode Found MSI capability
pcie_portdrv_probe->Dev[02fd:10de] has invalid IRQ. Check vendor BIOS
assign_interrupt_mode Found MSI capability
Real Time Clock Driver v1.12ac
hpet_acpi_add: no address or irqs in _CRS
Non-volatile memory driver v1.2
Linux agpgart interface v0.101 (c) Dave Jones
Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing disabled
serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
RAMDISK driver initialized: 16 RAM disks of 128000K size 1024 blocksize
serio: i8042 AUX port at 0x60,0x64 irq 12
serio: i8042 KBD port at 0x60,0x64 irq 1
mice: PS/2 mouse device common for all mice
input: PC Speaker as /class/input/input0
md: md driver 0.90.3 MAX_MD_DEVS=256, MD_SB_DISKS=27
md: bitmap version 4.39
NET: Registered protocol family 1
ACPI: (supports S0 S1 S3 S4 S5)
Freeing unused kernel memory: 188k freed
Boot logging started on /dev/ttyS0(/dev/console) at Sat Jan 17 11:24:34 2009
Creating device nodes with udev
Loading ide-core
Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
Loading ide-disk
Loading scsi_modSCSI subsystem initialized

Loading sd_mod
Loading processor
Loading thermal
Loading libata
BIOS EDD facility v0.16 2004-Jun-25, 2 devices found
Loading sata_sis
Loading sis5513
Loading fanmd: raid0 personality registered for level 0

Loading edd
md: raid1 personality registered for level 1
Loading raid0
raid5: automatically using best checksumming function: generic_sse
Loading raid1
Loading xor
   generic_sse:  6479.000 MB/sec
raid5: using function: generic_sse (6479.000 MB/sec)
Loading raid456
raid6: int64x1   1894 MB/s
raid6: int64x2   2436 MB/s
raid6: int64x4   2428 MB/s
raid6: int64x8   1682 MB/s
raid6: sse2x1    2830 MB/s
raid6: sse2x2    3871 MB/s
raid6: sse2x4    3957 MB/s
raid6: using algorithm sse2x4 (3957 MB/s)
md: raid6 personality registered for level 6
md: raid5 personality registered for level 5
md: raid4 personality registered for level 4
md: linear personality registered for level -1

Loading jbd
Loading mbcache
md: md1 stopped.
Loading ext3
mdadm: no devices found for /dev/md1
Waiting for device /dev/root to appear:  ok
/dev/root: unknown volume type
invalid root filesystem -- exiting to /bin/sh
sh: no job control in this shell
Sorry für den Overload an Daten!
Last edited by shapeshift on 2009-01-18 11:54, edited 2 times in total.
Top
shapeshift
Posts: 18
Joined: 2003-02-16 00:05
 

Re: Rootserver RAID- / Bootproblem, 1&1

Post by shapeshift »

So kurzer Zwischenbericht, ich habe jetzt das RAID wieder hergestellt (md1, md5, md6, md7 ,md8).

Code: Select all

cat /proc/mdstat

Code: Select all

Personalities : [linear] [raid0] [raid1] [raid10] [raid6] [raid5] [raid4] [faulty]
md1 : active raid1 sdb1[1] sda1[0]
      987840 blocks [2/2] [UU]

md5 : active raid1 sdb5[1] sda5[0]
      4891648 blocks [2/2] [UU]

md6 : active raid1 sdb6[1] sda6[0]
      4891648 blocks [2/2] [UU]

md7 : active raid1 sdb7[1] sda7[0]
      19542976 blocks [2/2] [UU]

md8 : active raid1 sdb8[1] sda8[0]
      124013632 blocks [2/2] [UU]

unused devices: <none>
Wenn ich im Rescue-System bin funktioniert nach dem Mounten und Start von Plesk alles wunderbar, jetzt ist es aber so dass ich im "Normal"-Modus noch immer nicht booten kann:

Code: Select all

shutdown: sending all processes the TERM signal.powernowd[1713]: segfault at 0 ip 00007f2afc4eaf04 sp 00007fff047bee38 error 4..
 in libc-2.3.2.so[7f2afc46d000+122000]
shumd: md5 in immediate safe mode
md: md7 in immediate safe mode
md: md8 in immediate safe mode
md: md6 in immediate safe mode
md: md1 in immediate safe mode
md: stopping all md devices.
md: md5 switched to read-only mode.
md: md6 switched to read-only mode.
md: md7 switched to read-only mode.
md: md8 switched to read-only mode.
kvm: exiting hardware virtualization
sd 1:0:0:0: [sdb] Synchronizing SCSI cache
sd 0:0:0:0: [sda] Synchronizing SCSI cache
forcedeth 0000:00:14.0: PCI INT A disabled
Restarting system.
machine restart

LILO 22.7 boot:
Loading Linux............................................................................................
BIOS data check successful
Bootdata ok (command line is auto BOOT_IMAGE=Linux ro root=901 console=tty0 console=ttyS0,57600 panic=30)
Linux version 2.6.18.8-0.7-default (geeko@buildhost) (gcc version 4.1.2 20061115 (prerelease) (SUSE Linux)) #1 SMP Tue Oct 2 17:21:08 UTC 2007
BIOS-provided physical RAM map:
 BIOS-e820: 0000000000000000 - 000000000009e000 (usable)
 BIOS-e820: 000000000009e000 - 00000000000a0000 (reserved)
 BIOS-e820: 00000000000d0000 - 0000000000100000 (reserved)
 BIOS-e820: 0000000000100000 - 000000003df10000 (usable)
 BIOS-e820: 000000003df10000 - 000000003df16000 (ACPI data)
 BIOS-e820: 000000003df16000 - 000000003df80000 (ACPI NVS)
 BIOS-e820: 000000003df80000 - 0000000040000000 (reserved)
 BIOS-e820: 00000000fc000000 - 00000000fe000000 (reserved)
 BIOS-e820: 00000000fec00000 - 00000000fec10000 (reserved)
 BIOS-e820: 00000000fee00000 - 00000000fee01000 (reserved)
 BIOS-e820: 00000000fff80000 - 0000000100000000 (reserved)
DMI present.
Scanning NUMA topology in Northbridge 24
Number of nodes 1
Node 0 MemBase 0000000000000000 Limit 000000003df10000
Using node hash shift of 63
Bootmem setup node 0 0000000000000000-000000003df10000
Nvidia board detected. Ignoring ACPI timer override.
If you got timer trouble try acpi_use_timer_override
ACPI: PM-Timer IO Port: 0x1008
ACPI: LAPIC (acpi_id[0x00] lapic_id[0x00] enabled)
Processor #0 15:11 APIC version 16
ACPI: LAPIC (acpi_id[0x01] lapic_id[0x01] enabled)
Processor #1 15:11 APIC version 16
ACPI: LAPIC_NMI (acpi_id[0x00] high edge lint[0x1])
ACPI: LAPIC_NMI (acpi_id[0x01] high edge lint[0x1])
ACPI: IOAPIC (id[0x02] address[0xfec00000] gsi_base[0])
IOAPIC[0]: apic_id 2, version 17, address 0xfec00000, GSI 0-23
Setting APIC routing to physical flat
Using ACPI (MADT) for SMP configuration information
Allocating PCI resources starting at 50000000 (gap: 40000000:bc000000)
SMP: Allowing 2 CPUs, 0 hotplug CPUs
Built 1 zonelists.  Total pages: 248320
Kernel command line: auto BOOT_IMAGE=Linux ro root=901 console=tty0 console=ttyS0,57600 panic=30
Initializing CPU#0
PID hash table entries: 4096 (order: 12, 32768 bytes)
Disabling vsyscall due to use of PM timer
time.c: Using 3.579545 MHz WALL PM GTOD PM timer.
time.c: Detected 2109.648 MHz processor.
Console: colour VGA+ 80x25
Dentry cache hash table entries: 131072 (order: 8, 1048576 bytes)
Inode-cache hash table entries: 65536 (order: 7, 524288 bytes)
Checking aperture...
CPU 0: aperture @ 2218000000 size 32 MB
Aperture too small (32 MB)
No AGP bridge found
Memory: 991512k/1014848k available (1915k kernel code, 22944k reserved, 1282k data, 188k init)
Calibrating delay using timer specific routine.. 4223.89 BogoMIPS (lpj=8447784)
Security Framework v1.0.0 initialized
Mount-cache hash table entries: 256
CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line)
CPU: L2 Cache: 512K (64 bytes/line)
CPU 0/0 -> Node 0
CPU: Physical Processor ID: 0
CPU: Processor Core ID: 0
SMP alternatives: switching to UP code
checking if image is initramfs... it is
Freeing initrd memory: 3105k freed
ACPI: Core revision 20060707
Using local APIC timer interrupts.
result 12557442
Detected 12.557 MHz APIC timer.
SMP alternatives: switching to SMP code
Booting processor 1/2 APIC 0x1
Initializing CPU#1
Calibrating delay using timer specific routine.. 4219.46 BogoMIPS (lpj=8438921)
CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line)
CPU: L2 Cache: 512K (64 bytes/line)
CPU 1/1 -> Node 0
CPU: Physical Processor ID: 0
CPU: Processor Core ID: 1
AMD Athlon(tm) 64 X2 Dual Core Processor 4000+ stepping 01
CPU 1: Syncing TSC to CPU 0.
CPU 1: synchronized TSC with CPU 0 (last diff 0 cycles, maxerr 559 cycles)
Brought up 2 CPUs
testing NMI watchdog ... OK.
migration_cost=420
NET: Registered protocol family 16
ACPI: bus type pci registered
PCI: Using MMCONFIG at fc000000
PCI: No mmconfig possible on device 0:18
ACPI: Interpreter enabled
ACPI: Using IOAPIC for interrupt routing
ACPI: PCI Root Bridge [PCI0] (0000:00)
PCI: Transparent bridge - 0000:00:10.0
ACPI: Device [TPM] status [00000008]: functional but not present; setting present
ACPI: PCI Interrupt Link [LNKA] (IRQs 5 7 10 11 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LNKB] (IRQs 5 7 10 11 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LNKC] (IRQs<7>Losing some ticks... checking if CPU frequency changed.
 5 7 10 11 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LNKD] (IRQs 5 7 10 11 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LNKE] (IRQs 16 17 18 19 20 21 22 23) *0, disabled.
ACPI: PCI Interrupt Link [LNKF] (IRQs 16 17 18 19 20 21 22 23) *0, disabled.
ACPI: PCI Interrupt Link [LNKG] (IRQs 16 17 18 19 20 21 22 23) *10
ACPI: PCI Interrupt Link [LNKH] (IRQs 16 17 18 19 20 21 22 23) *0, disabled.
ACPI: PCI Interrupt Link [LNKI] (IRQs 16 17 18 19 20 21 22 23) *7
ACPI: PCI Interrupt Link [LNKJ] (IRQs 16 17 18 19 20 21 22 23) *11
ACPI: PCI Interrupt Link [LNKK] (IRQs 16 17 18 19 20 21 22 23) *10
ACPI: PCI Interrupt Link [LNKL] (IRQs 16 17 18 19 20 21 22 23) *11
ACPI: PCI Interrupt Link [LNKM] (IRQs 16 17 18 19 20 21 22 23) *0, disabled.
ACPI: PCI Interrupt Link [LNKN] (IRQs 16 17 18 19 20 21 22 23) *5
ACPI: PCI Interrupt Link [LNKO] (IRQs 16 17 18 19 20 21 22 23) *0, disabled.
ACPI: PCI Interrupt Link [LNKP] (IRQs 16 17 18 19 20 21 22 23) *0, disabled.
ACPI: Device [FDC] status [00000008]: functional but not present; setting present
ACPI: Device [LPT] status [00000008]: functional but not present; setting present
ACPI: Device [ECP] status [00000008]: functional but not present; setting present
ACPI: Device [COM2] status [00000008]: functional but not present; setting present
PCI: Using ACPI for IRQ routing
PCI: If a device doesn't work, try "pci=routeirq".  If it helps, post a report
PCI-DMA: Disabling IOMMU.
PCI: Bridge: 0000:00:02.0
  IO window: disabled.
  MEM window: disabled.
  PREFETCH window: disabled.
PCI: Bridge: 0000:00:03.0
  IO window: disabled.
  MEM window: disabled.
  PREFETCH window: disabled.
PCI: Bridge: 0000:00:10.0
  IO window: disabled.
  MEM window: disabled.
  PREFETCH window: disabled.
NET: Registered protocol family 2
IP route cache hash table entries: 32768 (order: 6, 262144 bytes)
TCP established hash table entries: 131072 (order: 9, 2097152 bytes)
TCP bind hash table entries: 65536 (order: 8, 1048576 bytes)
TCP: Hash tables configured (established 131072 bind 65536)
TCP reno registered
Simple Boot Flag at 0x36 set to 0x80
audit: initializing netlink socket (disabled)
audit(1232222646.940:1): initialized
Total HugeTLB memory allocated, 0
VFS: Disk quotas dquot_6.5.1
Dquot-cache hash table entries: 512 (order 0, 4096 bytes)
Initializing Cryptographic API
io scheduler noop registered
io scheduler anticipatory registered
io scheduler deadline registered
io scheduler cfq registered (default)
pcie_portdrv_probe->Dev[02fc:10de] has invalid IRQ. Check vendor BIOS
assign_interrupt_mode Found MSI capability
pcie_portdrv_probe->Dev[02fd:10de] has invalid IRQ. Check vendor BIOS
assign_interrupt_mode Found MSI capability
Real Time Clock Driver v1.12ac
hpet_acpi_add: no address or irqs in _CRS
Non-volatile memory driver v1.2
Linux agpgart interface v0.101 (c) Dave Jones
Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing disabled
serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
RAMDISK driver initialized: 16 RAM disks of 128000K size 1024 blocksize
serio: i8042 AUX port at 0x60,0x64 irq 12
serio: i8042 KBD port at 0x60,0x64 irq 1
mice: PS/2 mouse device common for all mice
input: PC Speaker as /class/input/input0
md: md driver 0.90.3 MAX_MD_DEVS=256, MD_SB_DISKS=27
md: bitmap version 4.39
NET: Registered protocol family 1
ACPI: (supports S0 S1 S3 S4 S5)
Freeing unused kernel memory: 188k freed
Boot logging started on /dev/ttyS0(/dev/console) at Sat Jan 17 20:04:07 2009
Creating device nodes with udev
Loading ide-core
Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
Loading ide-disk
Loading scsi_modSCSI subsystem initialized

Loading sd_mod
Loading processor
Loading thermal
Loading libata
Loading sata_sis
BIOS EDD facility v0.16 2004-Jun-25, 2 devices found
Loading sis5513
Loading fan
md: raid0 personality registered for level 0
Loading edd
md: raid1 personality registered for level 1
Loading raid0
Loading raid1
raid5: automatically using best checksumming function: generic_sse
Loading xor
   generic_sse:  6477.000 MB/sec
raid5: using function: generic_sse (6477.000 MB/sec)
Loading raid456
raid6: int64x1   1895 MB/s
raid6: int64x2   2438 MB/s
raid6: int64x4   2443 MB/s
raid6: int64x8   1686 MB/s
raid6: sse2x1    2829 MB/s
raid6: sse2x2    3857 MB/s
raid6: sse2x4    3939 MB/s
raid6: using algorithm sse2x4 (3939 MB/s)
md: raid6 personality registered for level 6
md: raid5 personality registered for level 5
md: raid4 personality registered for level 4
md: linear personality registered for level -1

Loading jbd
Loading mbcache
md: md1 stopped.
Loading ext3
mdadm: no devices found for /dev/md1
Waiting for device /dev/root to appear:  ok
/dev/root: unknown volume type
invalid root filesystem -- exiting to /bin/sh
sh: no job control in this shell
Nach wie vor besteht das Problem "md: md1 stopped. | mdadm: no devices found for /dev/md1 | /dev/root: unknown volume type".
Muss ich die lilo.conf manuell anpassen (bei Aufruf "lilo" wird nichts geändert), oder doch einen anderen Kernel einspielen, hier mal das boot-Verzeichnis (ist ein alter Kernel):

Code: Select all

total 13024
   4 drwxr-xr-x  4 root root    4096 Jan 17 20:58 .
 152 -rw-------  1 root root  147968 Jan 17 20:58 map
   4 drwxr-xr-x 25 root root    4096 Jan 17 20:11 ..
 376 -rw-r--r--  1 root root  379904 Jan 29  2008 message
   0 lrwxrwxrwx  1 root root      27 Jan 29  2008 initrd -> initrd-2.6.18.8-0.7-default
3112 -rw-r--r--  1 root root 3179768 Jan 29  2008 initrd-2.6.18.8-0.7-default
   0 lrwxrwxrwx  1 root root      28 Jan 29  2008 vmlinuz -> vmlinuz-2.6.18.8-0.7-default
1268 -rw-r--r--  1 root root 1290771 Nov  8  2007 System.map-2.6.20.21-071108a
2812 -rw-r--r--  1 root root 2875376 Nov  8  2007 vmlinuz-2.6.20.21-071108a
  36 -rw-r--r--  1 root root   34910 Nov  8  2007 config-2.6.20.21-071108a
   4 drwxr-xr-x  2 root root    4096 Oct 31  2007 grub
 336 -rw-r--r--  1 root root  338740 Oct  3  2007 symtypes-2.6.18.8-0.7-default.gz
  92 -rw-r--r--  1 root root   86462 Oct  3  2007 symsets-2.6.18.8-0.7-default.tar.gz
 104 -rw-r--r--  1 root root   99320 Oct  3  2007 symvers-2.6.18.8-0.7-default.gz
  68 -rw-r--r--  1 root root   64134 Oct  3  2007 config-2.6.18.8-0.7-default
2072 -rwxr-xr-x  1 root root 2114978 Oct  3  2007 vmlinux-2.6.18.8-0.7-default.gz
1588 -rw-r--r--  1 root root 1618384 Oct  3  2007 vmlinuz-2.6.18.8-0.7-default
 936 -rw-r--r--  1 root root  954130 Oct  3  2007 System.map-2.6.18.8-0.7-default
   4 -rw-------  1 root root     512 Sep 19  2007 backup_mbr
  48 drwx------  2 root root   49152 Feb  6  2006 lost+found
   4 -rw-r--r--  1 root root     512 Feb  6  2006 boot.0810
   4 -rw-r--r--  1 root root     512 Feb  6  2006 boot.0800
   0 lrwxrwxrwx  1 root root       1 Feb  6  2006 boot -> .
   0 lrwxrwxrwx  1 root root      26 Feb  6  2006 initrd.old -> initrd-2.6.18.2-34-default
   0 lrwxrwxrwx  1 root root      27 Feb  6  2006 vmlinux.old -> vmlinuz-2.6.18.2-34-default
Hier nochmals lilo.conf, die ist noch immer unverändert, Device-Zuordnung sollte stimmen (boot, root usw.):

Code: Select all

# Modified by YaST2. Last modification on Tue Jan 29 00:25:01 CET 2008
boot = /dev/sda
root = /dev/md1
install = /boot/boot.b
vga = normal
timeout = 60
prompt
lba32
read-only
default = Linux
serial = 0,57600n8
append = "console=ttyS0,57600 console=tty0"

image = /boot/vmlinuz-2.6.18.8-0.7-default
###Don't change this comment - YaST2 identifier: Original name: linux###
    label = Linux
    append = " console=tty0 console=ttyS0,57600 panic=30"
    initrd = /boot/initrd-2.6.18.8-0.7-default
    root = /dev/md1

image = /boot/vmlinuz-2.6.18.8-0.7-default
###Don't change this comment - YaST2 identifier: Original name: failsafe###
    label = Failsafe
    append = "showopts ide=nodma apm=off acpi=off noresume edd=off 3"
    initrd = /boot/initrd-2.6.18.8-0.7-default
    root = /dev/md1


image = /boot/vmlinuz
    label = lxser
    append = " console=tty0 console=ttyS0,57600 panic=30"


image = /boot/vmlinuz
    label = lx
Ich danke im voraus für alle Tipps, Ideen und Denkanstöße !
Viele Grüße!
Top
shapeshift
Posts: 18
Joined: 2003-02-16 00:05
 

Re: Rootserver RAID- / Bootproblem, 1&1

Post by shapeshift »

und weiter gehts. ich habe jetzt den aktuellen Kernel von update.rootmaster.info gezogen (vmlinuz-2.6.27.9-20081215a für AMD64 aus local-updates Ordner) und wie folgt eingebunden:

boot-Verzeichnis:

Code: Select all

ls -aslt

Code: Select all

total 18256
   4 drwxr-xr-x  4 root root    4096 Jan 18 10:50 .
   0 lrwxrwxrwx  1 root root      26 Jan 18 10:50 vmlinuz -> vmlinuz-2.6.27.9-20081215a
  48 -rw-r--r--  1 root root   47376 Jan 18 10:39 config-2.6.27.9-20081215a
1692 -rw-r--r--  1 root root 1728121 Jan 18 10:38 System.map-2.6.27.9-20081215a
3492 -rw-r--r--  1 root root 3569328 Jan 18 10:38 vmlinuz-2.6.27.9-20081215a
 152 -rw-------  1 root root  147968 Jan 17 20:58 map
   4 drwxr-xr-x 25 root root    4096 Jan 17 20:11 ..
 376 -rw-r--r--  1 root root  379904 Jan 29  2008 message
   0 lrwxrwxrwx  1 root root      27 Jan 29  2008 initrd -> initrd-2.6.18.8-0.7-default
3112 -rw-r--r--  1 root root 3179768 Jan 29  2008 initrd-2.6.18.8-0.7-default
1268 -rw-r--r--  1 root root 1290771 Nov  8  2007 System.map-2.6.20.21-071108a
2812 -rw-r--r--  1 root root 2875376 Nov  8  2007 vmlinuz-2.6.20.21-071108a
  36 -rw-r--r--  1 root root   34910 Nov  8  2007 config-2.6.20.21-071108a
   4 drwxr-xr-x  2 root root    4096 Oct 31  2007 grub
 336 -rw-r--r--  1 root root  338740 Oct  3  2007 symtypes-2.6.18.8-0.7-default.gz
  92 -rw-r--r--  1 root root   86462 Oct  3  2007 symsets-2.6.18.8-0.7-default.tar.gz
 104 -rw-r--r--  1 root root   99320 Oct  3  2007 symvers-2.6.18.8-0.7-default.gz
  68 -rw-r--r--  1 root root   64134 Oct  3  2007 config-2.6.18.8-0.7-default
2072 -rwxr-xr-x  1 root root 2114978 Oct  3  2007 vmlinux-2.6.18.8-0.7-default.gz
1588 -rw-r--r--  1 root root 1618384 Oct  3  2007 vmlinuz-2.6.18.8-0.7-default
 936 -rw-r--r--  1 root root  954130 Oct  3  2007 System.map-2.6.18.8-0.7-default
   4 -rw-------  1 root root     512 Sep 19  2007 backup_mbr
  48 drwx------  2 root root   49152 Feb  6  2006 lost+found
   4 -rw-r--r--  1 root root     512 Feb  6  2006 boot.0810
   4 -rw-r--r--  1 root root     512 Feb  6  2006 boot.0800
   0 lrwxrwxrwx  1 root root       1 Feb  6  2006 boot -> .
   0 lrwxrwxrwx  1 root root      26 Feb  6  2006 initrd.old -> initrd-2.6.18.2-34-default
   0 lrwxrwxrwx  1 root root      27 Feb  6  2006 vmlinux.old -> vmlinuz-2.6.18.2-34-default
------------------------------

Code: Select all

 cat /etc/lilo.conf

Code: Select all

# Modified by YaST2. Last modification on Tue Jan 29 00:25:01 CET 2008
boot = /dev/sda
root = /dev/md1
install = /boot/boot.b
vga = normal
timeout = 60
prompt
lba32
read-only
default = Linux
serial = 0,57600n8
append = "console=ttyS0,57600 console=tty0"

# image = /boot/vmlinuz-2.6.18.8-0.7-default
image = /boot/vmlinuz-2.6.27.9-20081215a
###Don't change this comment - YaST2 identifier: Original name: linux###
    label = Linux
    append = " console=tty0 console=ttyS0,57600 panic=30"
    # initrd = /boot/initrd-2.6.18.8-0.7-default
    root = /dev/md1

# image = /boot/vmlinuz-2.6.18.8-0.7-default
image = /boot/vmlinuz-2.6.27.9-20081215a
###Don't change this comment - YaST2 identifier: Original name: failsafe###
    label = Failsafe
    append = "showopts ide=nodma apm=off acpi=off noresume edd=off 3"
    # initrd = /boot/initrd-2.6.18.8-0.7-default
    root = /dev/md1


image = /boot/vmlinuz
    label = lxser
    append = " console=tty0 console=ttyS0,57600 panic=30"


image = /boot/vmlinuz
    label = lx
------------------------------

So dann noch Lilo gestartet und dann funktioniert schonmal das Neustarten :)
Allerdings sind jetzt noch einige Fehlermeldungen vorhanden, wäre schön wenn Ihr mir da kurz weiterhelfen könntet:

Auszüge aus boot.msg:

"System.map-2.6.27.9-20081215a" und "map" existieren im /boot/ - weiss nicht warum diese Meldung kommt?:

Code: Select all

Inspecting /boot/System.map-2.6.27.9-20081215a
Cannot find map file.
No module symbols loaded - kernel modules not enabled.
Was bedeutet dies? Ist die symbol table notwendig?:

Code: Select all

Cannot build symbol table - disabling symbol lookups
Werden davon Module benötigt (ac, battery...) oder sind die allesamt unwichtig?:

Code: Select all

modprobe: FATAL: Module ac not found.
modprobe: FATAL: Module battery not found.
modprobe: FATAL: Module button not found.
modprobe: FATAL: Module fan not found.
modprobe: FATAL: Module processor not found.
modprobe: FATAL: Module thermal not found.
modprobe: FATAL: Module asus_acpi not found.
modprobe: FATAL: Module ibm_acpi not found.
modprobe: FATAL: Module toshiba_acpi not found.
modprobe: FATAL: Module sony_acpi not found.
modprobe: FATAL: Module pcc_acpi not found.
modprobe: FATAL: Module ibm_acpi not found.
modprobe: FATAL: Module toshiba_acpi not found.
modprobe: FATAL: Module sony_acpi not found.
modprobe: FATAL: Module pcc_acpi not found.
[/quote]

ACPI Module braucht man ja auch nicht oder?:
[quote][acpid]: starting up
acpid: loading ACPI modules ( ) failed
acpid: will not skip unsupported modules
acpid: probing laptop ACPI modules
acpid: added to /var/lib/acpi/laptop_modulesdone
Starting acpid done
[acpid]: 0 rules loaded
Hier ist es nur die PSA (Plesk-) Firewall die nicht installiert ist, das sollte OK so sein?:

Code: Select all

Master Resource Control: runlevel 3 has been reached
Failed services in runlevel 3: acpid psa-firewall
Skipped services in runlevel 3: irq_balancer microcode
Keine Ahnung was für ein Prozess das ist:

Code: Select all

<notice>killproc: kill(3272,3)

Vielen Dank!
Top

Return to “Systemadministration”